Young Shin Industries Ltd. – South Korea | Revolutionary Diecutting Technology for the Future
///Young Shin Quest 270
Young Shin Quest 2702018-11-16T02:25:59+00:00

Young Shin Quest 270

The Quest 270 is a die cutter specifically developed by South Korean-based Young Shin Industries to address the growing need for die cutting short-run digital printing output.  The global digital printing industry will reach a volume of $187.7 billion in 2018 up from $131.5 billion in 2013 necessitating the need to address this growing segment of the industry.

The Quest 270 die cutter for short-run output provides advantages such as:

  • A wide variety of sheet sizes from 2700 x 1700 mm (max.) to 650 x 450 mm (min.)
  • Low entry cost that provides the precision and speed of die cutting short run digital printing jobs.
  • Can reduce the job set-up time by half, compared to a non-short run die cutter.  Estimated set-up time for the Young Shin Quest 270 Die Cutter is 10 to 15 minutes.
  • Efficiently and cost-effectively handles short runs from 10 sheets to 2,500 pieces.
  • The Quest 270 is modestly sized, fitting into existing environments.
  • Allows the facility to streamline the use of existing equipment for longer run jobs preventing the necessity of stopping and re-starting expensive and more complex equipment.
  • Enhances your operation’s range of jobs with higher productivity and greater profitability.
  • The Cost of Ownership of the Young Shin Quest 270 die cutter is astonishingly low.
Download PDF Floor Plan
Specification Quest 270
Maximum Sheet Size 2700 x 1700 mm
Minimum Sheet Size 650 x 450 mm
Maximum Cutting Size 2710 x 1710 mm
Maximum Sheet Thickness .99 mm up to optionally 76 mm
Maximum Speed 300 SPH
Maximum Cutting Pressure 500 tons
Moving Table Type = Stroke: Knuckle
Total Length 4.47 m
Total Width (Inc. Oper. Platform) 5.63 m
Total Height 2.5 m
Total Weight 78 tons
FEEDING SECTION

FEEDING SECTION

The Quest 270’s flatbed technology increases productivity by 10% – 15% since a new sheet can be placed on the platen while removing the completed die cut sheet without sheet waste falling into the machine.

DIE-CUTTING SECTION

DIECUTTING SECTION

Includes sophisticated electronics at the front of the unit that control the Quest 270’s pressure settings with an easy-to-use four-button system that can be easily adjusted and precisely aligned.

TOUCH SCREEN

TOUCH SCREEN

Clear and simple readings ensure quick problem resolution. Operator-friendly controls allow easy adjustments. Machine position read out.

EXPANDED SUBSTRATES

EXPANDED SUBSTRATES

The Quest 270 includes an option to die cut up to 76.2 mm substrates including triple wall corrugated. After removing the Spacing Block, the height of the knives can cut and crease triple wall die board up to 76.2 mm.

Remote Diagnostics

REMOTE DIAGNOSTICS

Remote diagnostics are integrated into the Quest 270. The Touch Screen serves as a monitor while safety sensors are equipped on the moving (in/out) cutting plate. Aerial sensors are positioned on both sides of the cutting plate. UL labeled sensor and motor are included. The electrical panel is in the rear side of the unit. A Key Switch is included. The Quest 270 utilizes the eWon System for remote diagnostics.

Chase and Tool Changeover

CHASE AND TOOL CHANGEOVER

The Quest 270’s chase frame can be easily removed from the front of the machine directly above the cutting plate providing easy, yet highly-accurate, operation of the die cutter accelerating speed and turnaround time as compared to older-style clamshell devices.

Safety

SAFETY

Specifically designed to facilitate the make-ready process, expedite the set-up procedures and provide swift and safe operation with both lasers and light curtains to guard against improper or unsafe operations by the operator.

Speed and Control

SPEED AND CONTROL

Variable speeds on the Quest 270 include four (4) operating modes: Single cycle, continuous cycle, dwell and variable speed control of the cutting plate.

Maintenance

MAINTENANCE

Mechanics are positioned within a self-contained area providing automatic lubrication of moving components with indicator panels and dials positioned within clear sight of the operator. Daily maintenance of air gun removes debris from the operating elements of the device.

Additional Options

ADDITIONAL OPTIONS

Options include a Wide Opening complete with filler plate to facilitate easy and rapid changeover between traditional jobs and honeycomb board. A heated bed preventing “bruising” for clear plastic substrates is available prolonging the tool and sealing the plastic. Both feeding and delivery tables are available.

Electronics

ELECTRONICS

The Quest 270 integrates world-recognized and easily available (off-the-shelf) components such as Siemens, Omron and Mitsubishi PLC’s.

Download PDF Brochure

Young Shin Quest 270

WOULD YOU LIKE MORE INFORMATION?

REQUEST INFORMATION
REQUEST A PROPOSAL